accessories and attachments of lathe machine pdf

Accessories and attachments of lathe machine pdf

File Name: accessories and attachments of lathe machine .zip
Size: 1350Kb
Published: 23.04.2021

What are Different Lathe Attachments and Accessories?

Uploaded by

Welcome to Scribd!

Lathe-Types, Parts, Feed Mechanisms, Specifications,Lathe Accessories and Attachments,Lathe...

The three jaw universal chuck, as shown in Fig. Thus chuck is used for holding round and hexagonal work. It is used to hold hollow work pieces to machine their external surface.

Hello Readers, today in this paper we will discuss Lathe Machine's Accessories and Attachments, after complete reading this article you will understand the devices which are used in lathe machine, and able to differentiate between Lathe Accessories and Attachments. So let's get started. The Lathe Machine Accessories are those which are used for holding and supporting the work material or for holding the cutting tool.

What are Different Lathe Attachments and Accessories?

Lathe is a machine tool which holds the work between two rigid and strong supports, called centers, or in a chuck or face plate. The cutting tool is rigidly held and supported in a tool post and is fed against the revolving work.

While the work revolves about its own axis, the tool is made to move either parallel to Cylindrical surface or at an angle with the axis Tapered surface to cut the desired material. Simplest of all types of lathe Contains Bed, Headstock, Tailstock, Tool post on adjustable slide No feed box, Lead screw, Carriage Headstock spindle speed to rpm Applications: Wood working, spinning, polishing etc. Types of Lathe 2. Engine or Center lathe Most widely used Early lathes were driven by steam engines and so the name engine lathe Heavy duty Head stock is much more robust in construction Contains additional mechanism for multiple speeds Carriage, Feed rod and Lead screw are available and hence, longitudinal and.

Tool room lathe Greater accuracy More versatility Wide range of speeds and feeds Applications: Precision work on tools, dies,. Used for special purposes Wheel lathe: For finishing journals, turning locomotive wheels Gap-bed lathe: A section of bed adjacent to tailstock is.

Automatic control: Once the tools are set and the machine starts, all the operations will be performed automatically.

Workpiece material Cutting tool material Type of operation Workpiece size Surface finish Cutting fluid Rigidity of machine tool. By belt drive on cone pulley fitted on the headstock spindle with or without a back gear arrangement.

In a belt driven back geared headstock, multiple speeds can be obtained 1. Direct speed or back gear out 2. Indirect speed or back gear in.

Cross feed facing, parting, etc. Angular feed taper turning, chamfering, etc. Tumbler gears are used to give the desired direction of movement to the lathe carriage, via lead screw or feed rod. Log in Get Started. If you can't read please download the document.

Download for free Report this document. Embed Size px x x x x Speed lathe Simplest of all types of lathe Contains Bed, Headstock, Tailstock, Tool post on adjustable slide No feed box, Lead screw, Carriage Headstock spindle speed to rpm Applications: Wood working, spinning, polishing etc.

Machine Tools 12 Types of Lathe 2. Bench lathe Small lathe, mounted on a bench Just a scaled version of engine lathe Used for small and precision work 4. Tool room lathe Greater accuracy More versatility Wide range of speeds and feeds Applications: Precision work on tools, dies, gauges Machine Tools 14 Capstan and Turret Lathes Tailstock of an engine lathe is replaced by a hexagonal turret Several tools fitted on the turret are fed into work in proper sequence to carryout different operations in one setting Hence used for production work Capstan lathe Turret with its saddle can move for a short distance over the sub bed.

Special purpose lathes Used for special purposes Wheel lathe: For finishing journals, turning locomotive wheels Gap-bed lathe: A section of bed adjacent to tailstock is removable thereby allowing very large diameter work to swing Duplicating lathe: To duplicate the shape of a template on to a workpiece Wheel lathe Duplicating lathe Machine Tools 16 Types of Lathe 7.

CNC lathe Computer Numerical Control Wide variety of process capability Multiple axes Indexing and contouring head On-line and off-line programming available Equipped with one or more turrets Each turret is equipped with a variety of tools Machine Tools 18 The Bed Rigid to withstand the cutting forces Massive, sufficient to absorb vibration Resist the torsional stresses set up. Should be seasoned naturally to avoid distortion.

Threaded end 2. Taper sleeve 3. Live center 4. Threaded nose 5. By all gear drive using sliding gears or clutches. By variable speed motor. Types Longitudinal feed cylindrical turning, thread cutting, etc. Sliding gear mechanism 2. Sliding clutch mechanism 3. Gear cone and Norton feed gear 4. Sliding key mechanism 5.

Uploaded by

In this article, you will learn what are different Lathe Attachments and Accessories for lathe machine and also you can download the PDF file of this article at the end. A lathe is a machine that holds the workpiece on a chuck and tool on a toolpost, the lathe machine rotates the workpiece about an axis to perform different lathe operations such as turning, facing, chamfering, thread cutting, knurling, drilling and more with tools that are applied to the workpiece to design an object with symmetry about that axis. Read more on: 22 Different Types of Lathe Operations. The most common methods of holding the workpiece in a lathe are between the two centres i. The different types of centres are used for different types of workpieces and also for specific purposes. The important types of centres used as shown in the figure below. This is very important of all other centres and here the tip is made of hard material.

Home About Wiki Tools Contacts. In this operation, the workpiece is revolved in a chuck or a faceplate and the tools which are fitted to the tool post is fed into the work. In the case of a lathe, the taper on a given workpiece is obtained by tuning the job and feeding the tool at an angle to produce a gradual increase or decrease in the diameter of the workpiece. Using a die handle is a common method of external thread cutting on the lathe. The base of the compound rest is graduated in degrees. A trained Lathes can be divided into three types for easy identification:operator can accomplish more machining jobs with the engine lathes, turret lathes, and special purpose lathes.

Skip to content. All Homes Search Contact. We provide high-precision, high-speed and high-rigidity products in line with customers' needs, underpinned by the precision technologies we have been developing ever since TSUGAMI was first established. It is necessary for turning angles and boring short tapers. Tool setting gauge is used for this purpose. The cross slide is first made free from lead screw by hinder screw.


Lathe Machine Accessories: · Face Plate · Catch plate or Dog plate · Mandrel · Steady rest · Follower rest · Chuck.


Welcome to Scribd!

Accessories are the tools and equipment used in routine lathe machining operations. Attachments are special fixtures that may be mounted on the lathe to expand the use of the lathe to include taper cutting, milling, and grinding. Some of the common accessories and attachments are described in the following paragraphs.

Anyone seeking for finance support should contact them on lfdsloans outlook. Amazing knowledge and I like to share this kind of information with my friends and hope they like it they why I do vapor chamber. We provide first-class quality Lathe Machines in Pakistan. Automobiles Machinery, tools and their services included. Get instant price quote from Noor MC.

Engine lathe’s attachments accessories

Please note that our site uses cookies that are used to improve the services we offer and to optimize the user experience.

Lathe-Types, Parts, Feed Mechanisms, Specifications,Lathe Accessories and Attachments,Lathe...

Техники обнимали друг друга, подбрасывая вверх длинные полосы распечаток. Бринкерхофф обнимал Мидж. Соши заливалась слезами. - Джабба, - спросил Фонтейн, - много они похитили. - Совсем мало, - сказал Джабба, посмотрев на монитор.  - Всего лишь какие-то обрывки, в полном виде -. Фонтейн медленно кивнул и улыбнулся одними уголками губ.

Ему казалось, что с него сорваны все внешние покровы. Не было ни страха, ни ощущения своей значимости - исчезло. Он остался нагим - лишь плоть и кости перед лицом Господа.

Упав, он устроил замыкание основного электропитания шифровалки. Но еще более страшной ей показалась другая фигура, прятавшаяся в тени, где-то в середине длинной лестницы. Ошибиться было невозможно.

2 comments

  • Chaitingchanga1972 23.04.2021 at 20:20

    Slideshare uses cookies to improve functionality and performance, and to provide you with relevant advertising.

    Reply
  • Freya N. 27.04.2021 at 19:10

    Lathe is a machine tool which holds the work between two rigid and strong supports, called centers, or in a chuck or face plate.

    Reply

Leave a reply